Construction Lifting Equipment Hammered Tower Crane Qtz Series Tower Crane Tc7021
Technical data of tower crane TC7021
Main structure type: assemble type; top slewing, horizontal jib trolleying car,external climbing, stationary model.
Hoisting mechanism allocation way: frequency motors+electrical hydraulic drum brake+gear reducer
Trolleying mechanism allocation way: conical rotor motor+planetary reducer
Electrical control mode: Linkage set+frequency adjusting speed
Mast section: (L×W×H,××): 2000×2000×3000
Base section:2000×2000×7500
Material of main chord:∠200×20/Q355B
Base section:∠200×20/Q355B+φ50/Q235B.
Hoisting jib size: (W×H,mm×mm):△1707×1446.5
Material of upper chord:
Section 1~3:100×10/Q355B; Section 4~10:100×8/Q460C
Material of lower chord:
Section 1~3:100×10/Q355B; Section 4~5:100×8/Q355B; Section 6~10:80×8/Q355B
Technical data of tower crane TC7021
Serial No. | Item | Unit | Specification | Note | ||||||
1 | Max. load | t | 12 | / | ||||||
2 | Rated load moment | t•m | 200 | / | ||||||
3 | Allowable work radius at rated load | m | 17.01 | / | ||||||
4 | Max. Work radius/min. Work radius | m | 70/3 | / | ||||||
5 | Allowable max. Load at max. Work radius | t | 2.10(2 falls);1.96(4 falls) | / | ||||||
6 | Work grade | / | A5 | / | ||||||
7 | Whole design weight(exclude balanced weight and pressed weight) | t | 69.6 | / | ||||||
8 | / | |||||||||
9 | Balanced weight(corresponding balanced weight/max. Work radius) | t/m | 21.5/70;19.5/65;17.5/60; 15.5/55;12.4/46 | / | ||||||
10 | Hoisting mechanism | Falls | / | 2 | 4 | / | ||||
Speed | m/min | 50 | 100 | / | 22.75 | 45.5 | / | / | ||
Work grade | / | M5 | / | |||||||
Motor power | kW | 55 | / | |||||||
Brake load moment | N•m | 1000 | / | |||||||
Wire steel rope model | / | 18 35W×7-5FC 1770 U sZ | / | |||||||
11 | Slewing mechanism | Slewing speed | r/min | 0~0.64 | / | |||||
Motor power | kW | 5.5kW×2 | / | |||||||
12 | Trolleying mechanism | Trolleying speed | m/min | 0~58 | / | |||||
Trolleying time | min | / | Trolleying car | |||||||
Motor power | kW | 7.5 | / | |||||||
13 | Work mechanism | Speed | m/min | / | Stationary | |||||
Motor power | kW | / | Stationary | |||||||
14 | Jacking mechanism | Jacking speed | m/min | 0.46 | / | |||||
Motor power | kW | 11 | / | |||||||
Rated work pressure | MPa | 31.5 | / |
Main structure type: assemble type; top slewing, horizontal jib trolleying car,external climbing, stationary model.
Hoisting mechanism allocation way: frequency motors+electrical hydraulic drum brake+gear reducer
Trolleying mechanism allocation way: conical rotor motor+planetary reducer
Electrical control mode: Linkage set+frequency adjusting speed
Mast section: (L×W×H,××): 2000×2000×3000
Base section:2000×2000×7500
Material of main chord:∠200×20/Q355B
Base section:∠200×20/Q355B+φ50/Q235B.
Hoisting jib size: (W×H,mm×mm):△1707×1446.5
Material of upper chord:
Section 1~3:100×10/Q355B; Section 4~10:100×8/Q460C
Material of lower chord:
Section 1~3:100×10/Q355B; Section 4~5:100×8/Q355B; Section 6~10:80×8/Q355B
Item | Performance | Parameter |
1 | Max. load(t) | 12t |
2 | Work radius(m) | 70m |
3 | Tip load(t) | 2.1 |
4 | Free standing height(m) | 60m |
5 | Max. height(m) | 180m |
6 | Mast section(m) | 2×2×3 |
7 | Material of mast section | 200×20 angle steel |
8 | Material of main sections | Q345B |
9 | Electrical parts | Siemens |
10 | Main motor | Jiangte |
11 | Main electrical cable | 200m |
12 | Main wire steel rope | Equipped with height 70m |
13 | Foundation bolts and balanced weight frame | All are equipped |
14 | Collar tie length from tower crane center to wall vertical distance | 5m |
Item | Unit | Performance | |||||||||||
Max.load | 2 falls | t | 6 | ||||||||||
4 falls | 12 | ||||||||||||
Min. Work radius/max. Work radius | m | 3.0 | |||||||||||
70 | |||||||||||||
Rated load moment | 2 falls | kN.m | 1750 | 1870 | 1930 | 2000 | 2000 | ||||||
4 falls | 1690 | 1800 | 1870 | 1940 | 1940 | ||||||||
Hoisting height | Free standing | m | 60 | ||||||||||
Attached | 2 falls | 184 | |||||||||||
4 falls | 92 | ||||||||||||
Hoisting speed | 2 falls | m/min | 0~90 | ||||||||||
4 falls | 0~45 | ||||||||||||
Hoisting mechanism powder | KW | 55 | |||||||||||
Slewing speed | R/min | 0~0.64 | |||||||||||
Slewing motor power | KW | 5.5X2 | |||||||||||
Trolleying speed | m/min | 0~58 | |||||||||||
Trolleying motor power | KW | 7.5 | |||||||||||
Jacking speed | m/min | 0.4 | |||||||||||
Jacking mechanism power | KW | 9 | |||||||||||
Whole height | m | 72.4 | |||||||||||
Jib tip to slewing center | 71.6/66.7/61.7/56.7/47.7 | ||||||||||||
Self weight | Jib tip to slewing center | 19 | |||||||||||
Self structure weight | t | 68 | |||||||||||
Balanced weight | 70 | 65 | 60 | 55 | 46 | ||||||||
21.5 | 19.5 | 17.5 | 15.5 | 12.4 | |||||||||
Allowable work temperature | ºC | -20+40 | |||||||||||
Wind grade under work | / | ≤6 grade | |||||||||||
Wind grade out of work | / | ≤11 grade | |||||||||||
Wind grade at installation height, dismentling, wind jacking, reducing section at max. Installation height | / | ≤4 grade | |||||||||||
Power | / | ~380V±10 |
Others | Grade | U5 |
Load condition | Q2 | |
Others | Work grade | A5 |
Mechanisms details
Hoisting mechanism | Model | 55JTVF30 | |||
Motor | Model | YZTPF250M-4-55KW | |||
Power frequency | Hz | 50 | |||
Rated speed | R/min | 1478 | |||
Power | Kw | 55 | |||
Reducer | Transmission ratio | 45 | |||
Drum | Rope capacity | m | 600 | ||
Layer | 6 | ||||
Diameter | mm | Φ720 | |||
Wire steel rope | Pulling force | N | 30000 | ||
Rate | Specification | 35WX7-18-1960I | |||
Hoisting speed (m/min) | 2 falls | M/min | 0-90 | 0-45 | |
4 falls | M/min | 0-45 | 0-22.5 | ||
Load (t) | 2 falls | T | 3 | 6 | |
4 falls | T | 6 | 12 | ||
Slewing mechanism | Model | HP55.130.180 | |||
Motor | Model | YTW132M2-6-5.5KW | |||
Power (kW) | 5.5 | ||||
Rotating speed (r/min) | 960 | ||||
Reducer | Transmission Ratio | 180 | |||
Small slewing gear pinion | Modulus m | 12 | |||
Teeth z | 18 | ||||
Coefficient factor | -0.5 | ||||
Slewing speed | r/min | 0-0.64 | |||
Slewing bearing | Model | 011.50.1600.10Z |
Coefficient factor | -0.5 | ||
Teeth z | 151 | ||
QTY. | Set | 2 | |
Hydraulic jacking mechanism | Hydraulic pump station | Relief valve Mpa | 31.5 |
Lower pressure relief Mpa | 6.5 | ||
Volume L/min | 12 | ||
Power Kw | 9 | ||
Oil tank L | >100 | ||
Jacking cylinder | Max. Pressure Mpa | 31.5 | |
Work pressure Mpa | 28 | ||
Cylinder diameter mm | Outer diameter Φ220 inner diameter Φ180 | ||
Rod diameter mm | Φ125 | ||
Stroke mm | 1640 | ||
Installation distance mm | 2160 | ||
Jacking speed m/min | 0.4 | ||
Trolleying mechanism | Model | BP7570X | |
Motor | Model | YBPE132M-4-7.5KW-B5 | |
Rotation speed m/min | 0-1440 | ||
Drum diameter mm | |||
Max. Pulling force m | 75 | ||
Wire steel rope | Specification | 6×19-9.3-1700-I | |
Length m | 170 | ||
Trolleying speed | m/min | 0-58 |
Loading chart
70 m
Jib length m | 3--17.01 | 18 | 20 | 22 | 24 | 26 | 28 | 30 | 32 | 34 | 36 | 38 | 40 | 42 | 44 | 46 |
4 falls kg | 12000 | 11274 | 10019 | 8993 | 8138 | 7415 | 6795 | 6257 | 5787 | 5371 | 5003 | 4673 | 4376 | 4107 | 3863 | 3640 |
Jib length m | 48 | 50 | 52 | 54 | 56 | 58 | 60 | 62 | 64 | 66 | 68 | 70 | ||||
4 falls kg | 3435 | 3247 | 3073 | 2913 | 2763 | 2624 | 2495 | 2373 | 2259 | 2152 | 2052 | 1957 | ||||
Jib length m | 3--31.68 | 32 | 34 | 36 | 38 | 40 | 42 | 44 | 46 | 48 | 50 | 52 | 54 | 56 | 58 | 60 |
2 falls kg | 6000 | 5930 | 5515 | 5146 | 4816 | 4519 | 4250 | 4006 | 3783 | 3578 | 3390 | 3216 | 3056 | 2906 | 2767 | 2638 |
Jib length m | 62 | 64 | 66 | 68 | 70 | |||||||||||
2 falls kg | 2516 | 2402 | 2295 | 2194 | 2100 |
65 m
Jib length m | 3--17.87 | 18 | 20 | 22 | 24 | 26 | 28 | 30 | 32 | 34 | 36 | 38 | 40 | 42 | 44 | 46 |
4 falls kg | 12000 | 11900 | 10585 | 9508 | 8610 | 7850 | 7198 | 6634 | 6140 | 5704 | 5317 | 4970 | 4659 | 4376 | 4120 | 3885 |
Jib length m | 48 | 50 | 52 | 54 | 56 | 58 | 60 | 62 | 64 | 65 | ||||||
4 falls kg | 3671 | 3473 | 3291 | 3122 | 2965 | 2819 | 2683 | 2556 | 2435 | 2378 | ||||||
Jib length m | 3--33.26 | 34 | 36 | 38 | 40 | 42 | 44 | 46 | 48 | 50 | 52 | 54 | 56 | 58 | 60 | 62 |
2 falls kg | 6000 | 5847 | 5459 | 5113 | 4800 | 4519 | 4262 | 4028 | 3813 | 3615 | 3433 | 3265 | 3108 | 2962 | 2826 | 2698 |
Jib length m | 64 | 65 | ||||||||||||||
2 falls kg | 2579 | 2521 |
60 m
Jib length m | 3--18.38 | 20 | 22 | 24 | 26 | 28 | 30 | 32 | 34 | 36 | 38 | 40 | 42 | 44 | 46 | 48 |
4 falls kg | 12000 | 10929 | 9820 | 8896 | 8115 | 7445 | 6864 | 6355 | 5907 | 5508 | 5151 | 4830 | 4540 | 4276 | 4035 | 3814 |
Jib length m | 50 | 52 | 54 | 56 | 58 | 60 | ||||||||||
4 falls kg | 3611 | 3423 | 3250 | 3088 | 2938 | 2798 | ||||||||||
Jib length m | 3--34.23 | 36 | 38 | 40 | 42 | 44 | 46 | 48 | 50 | 52 | 54 | 56 | 58 | 60 | ||
2 falls kg | 6000 | 5651 | 5295 | 4974 | 4683 | 4419 | 4178 | 3957 | 3754 | 3566 | 3393 | 3231 | 3080 | 2940 |
55 m
Jib length m | 3--18.91 | 20 | 22 | 24 | 26 | 28 | 30 | 32 | 34 | 36 | 38 | 40 | 42 | 44 | 45 | 46 |
4 falls kg | 12000 | 11275 | 10135 | 9185 | 8381 | 7691 | 7095 | 6571 | 6110 | 5700 | 5333 | 5003 | 4705 | 4434 | 4307 | 4185 |
Jib length m | 48 | 50 | 52 | 54 | 55 | |||||||||||
4 falls kg | 3958 | 3750 | 3556 | 3378 | 3293 | |||||||||||
Jib length m | 3--35.21 | 36 | 38 | 40 | 42 | 44 | 45 | 46 | 48 | 50 | 52 | 54 | 55 | |||
2 falls kg | 6000 | 5843 | 5477 | 5147 | 4848 | 4577 | 4450 | 4328 | 410 0 | 3893 | 3700 | 3520 | 3436 |
Jib length m | 3--18.91 | 20 | 22 | 24 | 26 | 28 | 30 | 32 | 34 | 36 | 38 | 40 | 42 | 44 | 45 | 46 |
4 fallskg | 12000 | 11275 | 10135 | 9185 | 8381 | 7691 | 7095 | 657 1 | 6110 | 5700 | 5333 | 500 3 | 4705 | 4434 | 4307 | 4185 |
Jib length m | 3--35.21 | 36 | 38 | 40 | 42 | 44 | 45 | 46 | ||||||||
2 fallskg | 6000 | 5843 | 5477 | 5147 | 4848 | 4577 | 4450 | 4328 |